Grease micro flow meter

Grease micro flow meter,Contact email: sales6@microflowmeter.com

With the development of society, the state pays more and more attention to the process automation instrumentation industry. However, the Grease micro flow meter industry has been in a vacancy and has been monopolized by major foreign brands such as Max, KRACHT, OVAL, etc. , People have long endured the expensive, long delivery, the sale can not be resolved in time and so on, such as semiconductor chip cutting a set of equipment on the millions, once the instrument problems, loss unimaginable, the slayer saw these phenomena, Resolutely resigned as senior engineer in the position of Siemens, the establishment of Shanghai Ji-sheng Instruments Co., Ltd., with great concentration on research and development of gear flow meter. We have Grease micro flow meter has been awarded a number of certificates, it is no exaggeration to say that Qishen production Grease micro flow meter For example, many customers replace the OVAL LSF40 with our CX-M5-AL because it costs less than half of the LSF40, but has twice the range than it does and has the same accuracy.

Shanghai JSN Micro Flow Meter CO.,LTD is a manufactory integrating scientific research, production, sales and service. It is located in the Shanghai Industrial Zone. The company is based on the people-oriented principle and takes the program as the degree. Competitive, product covers a variety of materials and super micro liquid flow meter,grease micro flow meter ,mass flow meter.spur gear flow meter,gear pump,gear metering pump etc instrumentation instrument. Widely applicable to trade settlement and measurement in various industries such as petroleum, chemical, environmental protection, metallurgy, electric power, transportation, food, medicine, military industry, scientific research, etc.
Grease micro flow meter is a new type of volumetric flowmeter, in addition to a positive displacement flowmeter with high accuracy, the flow is not sensitive to other advantages, there are the following advantages: Wide range, usually in the flow meter is 10: l, and Deep flowmeter is generally 100: 1, or even 1000: 1, the accuracy is still above 0.5%, suitable for high pressure flow measurement, the maximum pressure can reach 100Mpa, especially suitable for the measurement of small flow, the minimum measurement limit can be 0.3ml / min , Less affected by the viscosity characteristics of the medium, suitable for flow measurement under various viscosity conditions.

The grease micro flow meter's metering principle is the same as that of a general volumetric flow meter. The gears mesh with the fluid to be transported. The fluid to be measured enters the chamber through the oil inlet and pushes the rotor so that the fluid is continuously divided into the same volume of fluid. Oil port output. For every one rotation of the rotor, the flowmeter outputs the same volume of fluid in the four metering chambers in the figure. By measuring the number of revolutions of the elliptical gear rotor, the volume flow through the fluid can be obtained.
1、Iran GG GAS CONTROL: GC was established in 1990 is Iran's well-known natural gas odor company, odor is very expensive, the viscosity is only 0.55cp (20C), the requirement is the minimum flow of 0.05 L / H, commonly used flow: 0.1L /H, maximum flow 0.3 L/H, and require explosion protection.
2、US TOYOTA robot factory: TOYOTA's confidentiality is as strict as that of the product. The following are information that Toyota confirms and can disclose. Toyota purchased our flowmeter for the robot arm at the time, and the medium was petroleum (translated literally Petroleum) minimum flow: 2.5cc/min, common flow: 2.5cc/min, maximum flow: 20cc/min, viscosity is 4.3cp, there are two special requirements, 1) product quality must be light, because the robot arm one day Thousands of swings back and forth. 2) Because the arm swings indefinitely, the flowmeter must be universal. These two points we happen to have proprietary technology can satisfy.
3、Han's laser chip cutting: Han's laser is the world's leading manufacturer of laser processing equipment. In the semiconductor chip production process, because of heat generation, it is necessary to continuously spray cutting fluid, and our laser equipment and chips are high-end industries. High quality requirements, a slight careless product quality will be seriously affected, so Han's laser strictly to control the flow in 2ml/min.

Grease micro flow meter,Contact email: sales6@microflowmeter.com